Atlas Tire Changer Manual atlas Tire Changer
Atlas Tire Changer from atlas tire changer manual , source:ebay.com

Atlas Tire Changer Manual

Posted on

Atlas Tire Changer Manual
Allowed in order to the blog, within this time period I’m going to demonstrate in relation to atlas tire changer manual

PRINTING CHARACTERS AND SYMBOLS

Throughout this manual, the following symbols and printing characters are used to facilitate reading: Indicates the operations which need proper care
Indicates prohibition Indicates a possibility of danger for the operators
BOLD TYPE Important information

WARNING: before operating the lift and carrying out any adjustment, read
carefully chapter 7 “installation” where all proper operations for a better
functioning of the lift are shown.

CONTENTS

1 INTRODUCTION 4
2 GENERAL INFORMATION 6
3 TRANSPORT, UNPACKING AND STORAGE 9
4 INSTALLATION 10
5 OPERATION 16
6 INFLATING 20
7 MAINTENANCE 22
8 TROUBLESHOOTING 24
9 ELECTRIC AND PNEUMATIC DIAGRAM 25

CHAPTER 1 – INTRODUCTION

1.1 INTRODUCTION
Thank you for purchasing a product from the line of tire changers. The machine has been manufactured in accordance with the very best quality principles. Follow the simple instructions provided in this manual to ensure the correct operation and long life of the machine. Read the entire
manual thoroughly and make sure you understand it.

1.2 TYRE CHANGER IDENTIFICATION DATA
A complete description of the “Tire Changer Model” and the “Serial number” will make it easier for our technical assistance to provide service and will facilitate delivery of any required spare parts. For clarity and convenience, we have inserted the data of your tire changer in the box below. If there is any discrepancy between the data provided in this manual and that shown on the plate fixed to the tire changer, the latter should be taken as correct.

1.3 MANUAL KEEPING
For a proper use of this manual, the following is recommended:
x Keep the manual near the lift, in an easily accessible place.
x Keep the manual in an area protected from the damp.
x Use this manual properly without damaging it.
x Any use of the machine made by operators who are not familiar with the instructions and
procedures contained herein shall be forbidden.
This manual is an integral part of the manual: it shall be given to the new owner if and when the
machine is resold.
The illustrations have been made out of prototypes pictures. It is therefore
possible that some parts or components of standard production differ from those

1.4 GENERAL SAFETY PRECAUTIONS
The tire changer may only be used by specially trained and authorized expert personnel.
LOGO
Type:
Volt Amp Kw
Ph Hz
Year of manufacturing:
Air supply: 8-10 bar (115 – 145 PSI)
REV. 01 5 / 26
x Any tampering or modification to the equipment carried out without the manufacturer’s prior authorization will free him from all responsibility for damage caused directly or indirectly by the above actions.
x Removing or tampering with safety devices immediately invalidates the guarantee. x The tire changer comes complete with instruction and warning transfers which are designed
to be long-lasting. If they should for any reason be damaged or destroyed, please ask immediately for replacements from the manufacturer.

TO THE READER
Every effort has been made to ensure that the information contained in this manual is correct, complete
and up-to date. The manufacturer is not liable for any mistakes made when drawing up this manual and
reserves the right to make any changes due the development of the product, at any time

CHAPTER 2 – GENERAL INFORMATION
2.1 INTENDED USE
x This Semi-automatic tire changer has been designed and manufactured exclusively for removing and mounting tires from/onto rims from 10″ to 24″ and a maximum diameter of
1000 mm. x In particular THE MANUFACTURER cannot be held responsible for any damage caused through the use of this tire changer for purposes other than those specified in this manual, and therefore inappropriate, incorrect and unreasonable.

2.2 DESCRIPTION
G) Clamps
I) Mounting head
M) Mounting bar
N) Horizontal arm
P) Vertical arm
Q) Air supply
R) Bead breaker
S) Wheel support
T) Bead lifting lever
U) Clamp control pedal
V) Clamp control pedal
Z) Reverser control pedal
Y) Turntable
K) Locking lever
Fig . 1

2.3 DANGER WARNING SIGNS
REV. 01 8 / 26
2.4 TECHNICAL SPECIFICATION
External locking rim dimension
10” – 20”
11” – 21”
12” – 22”
Internal locking rim dimension
12”- 22”
13” – 23”
14” – 24”
Max. tire diameter 1000mm (39”)
Max tire width 420mm (17”)
Force on bead breaker blade (10 bar) 2500 kg
Working pressure 10 bar (145 psi)
Inflating pressure device max. 3.5 bar (50 psi)
Power supply voltage 110V 1Ph
Motor power 1.1 kw (1ph)
Rotating speed 7 – 14 rpm
Max spindle torch 1200 NM
Dimension 1050 x 760 x 950
Net weight 229 kg STND
Noise level in working condition < 70 dB (A)

CHAPTER 3 – TRANSPORTATION, UNPACKING AND STORAGE
3.1 TRANSPORTATION
x The tire changer must be transported in its original packaging and kept in the position shown
on the package itself.
x The packaged machine may be moved by means of a fork lift truck of suitable capacity. Insert
the forks at the points shown in figure 3.
3.2 UNPACKING
x Remove the protective cardboard and the nylon bag.
x Check that the equipment is in perfect condition, making sure that no parts are damaged or
missing. Use fig. 1 for reference.
If in doubt do not use the machine and contact your retailer.
3.3 STORAGE
In the event of storage for long periods of time, be sure to disconnect all sources of power and grease
the clamp sliding guides on the turntable to prevent them from oxidizing.

CHAPTER 4 – INSTALLATION
4.1 SPACE REQUIRED
When choosing the place of installation be sure that it complies with current safety
at work regulations.
x The tire changer must be connected to the main electric power supply and the compressed air
system. It is therefore advisable to install the machine near these power sources.
x The place of installation must also provide at least the space shown in pictures 4 – 4/A so as to
allow all parts of the machine to operate correctly and without any restriction.
x If the machine is installed outside it must be protected by a lean-to.
The tire changer with electric motor cannot be used in explosive atmospheres,
unless it is a proper version.

4.2 POSITIONING AND PARTS ASSEMBLY
4.2.1 Arm assembly
x Unscrew the pallet fixing screws and set the tire changer on the floor.
x Unscrew the 4 screws from the body, set the vertical arm into the proper seat and fix the screw
again (Fig. 5/a).
x Make sure the horizontal arm is on the vertical arm’s support and the pin is locked with nuts
and washers as shown in Fig. 5/b.
Before connecting all the power sources ALWAYS check your installations.
They must exactly correspond to those requested by the machine.
x Connect the machine to the compressed air network (Fig. 5/d)
x Mount the bead breaker arm as shown in Fig. 5/e:
– Set the arm “a” into the proper seat, set the screw into the hole and screw the nut

WITHOUT TIGHTENING.
– Set the pivot pin “b” into the hole on the arm and let the cylinder’s shaft pass through
the pin’s hole. Screw two nuts WITHOUT TIGHTENING.
– Set the spring by hooking it at the indicated points.
x Screw the bead breaker arm’s screw as indicated in Fig 5/f
x Screw the nut as indicated in Fig 5/g

4.2.2 Mounting and connecting the GT tank (optional)
x Fix the tank on the back side of the machine
body through the proper screw. Fig. 10.
x Demount the side panel.
x Route the hose (2), situated inside the machine
body, though the hole on the back side of the
body.
x Tighten the hose (2) to the bank through the
proper union.
4.2.3 Mounting and connecting the manometer
x Fix the manometer to the vertical arm
through the proper screw. Fig. 11.
x Route the connecting spiral hose through
the small hole on the back side of the
machine body.
x Connect the rilsan hose to the union of the
pressure limiting device, situated on the
inflating pedal.

4.3 COMMISSIONING
Any electric connection job must be carried out by professionally qualified
personnel.
Make sure that the power supply is right.
Make sure the connection of the phases is right. Improper electrical hook-up
can damage motor and will not be covered under warranty.
x Check to make sure the characteristics of your systems correspond to those required by the
machine. If you have to change the machine’s operating voltage, make the necessary
adjustments to the terminal board referring to the electric diagram in chapter 9.
x Connect the machine to the compressed air system by means of the air connection (Q) that
protrudes from the rear section.
Connect the machine to the electric network, which must be provided with line
fuses, a good earth plate in compliance with regulations in force and it must be
connected to an automatic circuit breaker (differential) set at 30 mA.
Should the tire-changer be lacking in electric plug, the user must set one, which
is at least 16 A and which conforms to the voltage of the machine, in compliance
with the regulations in force.

4.4 OPERATING TESTS
x When pedal (Z) is pressed down the turntable (Y) should turn in a clockwise direction. When
pedal is pulled up the turntable should turn in an anticlockwise direction.
If the turntable turns in the opposite direction to that shown, reverse two of the
wires in the tree-phase plug.
x Pressing the pedal (U) activates the bead
breaker (R); when the pedal is released the
bead breaker returns to its original position.
x Pressing the pedal (V) opens the four clamps
(G); when the pedal is pressed again they
close.
x Pressing the trigger on the airline gauge cause
air to be released from the head.

4.4.1 GT SYSTEM (optional)
Do NOT LEAN on the turntable during this operation. Possibly dirty dust on
turntable could offend the operator’s eyes. For the same reason, be carefully as
not to accidentally push the inflating pedal while working.
x When the pedal located on the left side of the machine
body is pushed down to its intermediate position (B),
air is released from the airline gauge.
x When the pedal (C) is pushed down completely, air is
released from the airline gauge with a powerful jet from
the nozzles located on the turntable clamps.
4.5 TURNTABLE LOCKING VALUE ADJUSTING
The tire changer turntable is preset by the manufacturer on a middle range measure from11” to 21”
ext. (considering the rim outer side and) from 13” – 23” int. (if you lock the rim from inner side).
It is however possible to change this dimension range in case of need when working on larger or
small rims; it is enough to change the position of the 4 clamps are shown in the figures below.
The obtainable value starts from a minimum of 10”-20” ext. and 12”-22” int. until a maximum of 12”-
22” ext. and 14”-24” int.
To change the position, proceed as follows:
x Unscrew screw (1) by means of the Allen wrench.
x Remove the locking clamp (2) and the slide piece (3).
x Align the slide hole with one of the guide holes (4) according to the locking dimensions you
want to set. Use the measures below for reference.
It is important to perform the above mentioned operation for all the 4 clamps to
avoid any unbalance in locking phase.
Fig. 13

CHAPTER 5 – OPERATION
Do not use the machine until you have read and understood the entire manual
and the warning provided.
Before carrying out any operation, deflate the tire and take off all the wheel
balancing weights.
The operation of the tire changer is divided into three parts:
a) BREAKING THE BEAD b) REMOVING THE TIRE c) MOUNTING THE TIRE
It is advised to equip the tire changer with the pressure regulator.
5.1 BREAKING THE BEAD
Bead breaking must be done with the utmost care and attention. When the bead
breaker pedal is operated the bead breaker arm moves quickly and powerfully.
Anything within its arrange of action can be in danger of being crushed.
x Check that the tire is deflated. If not, deflate it.
x Close the turntable clamps completely.
Bead breaking with the clamps in open position can be extremely dangerous for
operator’s hands.
During bead breaking operations NEVER touch the side of the tire.
x Position the wheel against the rubber stops on the right side of the tire changer (S).
x Position the bead breaker (R) against the tire bead at a distance of about 1 cm from the rim (fig.
8). Pay attention to the blade, which must operate correctly onto the tire and not onto the rim.
x Press down the pedal (U) to activate the bead breaker and release it when the blade has reached
the end of its travel or in any case when the bead is broken.
x Rotate the tire slightly and repeat the operation around the entire circumference if the rim and
from both sides until the bead is completely detached from the rim.

5.2 REMOVING THE TIRE
Before any operation make sure to remove the old wheel balancing weights and
check that the tire is deflated.
During arm tilting make sure that nobody stats behind the tire changer.
x Spread the supplied grease (or grease of a similar type) onto the tire bead.
Failure to use the grease could cause serious damage to the tire bead.
During rim locking MEVER keep your hands under the tire. For a correct
locking operation set the tire exactly in the middle of turntable.
Make sure that the rim is firmly fixed to the clamps.
Never keep your hands onto the wheel: the arm recovery to “working position”
could set the operator at risk of hand crushing between rim and mounting head.
x Lower the mounting bar (M) so that the mounting head (I) rests against the edge of the rim and
lock it using the lever (K). This will lock the arm in both vertical and horizontal direction and
move the mounting head (I) of about 2 mm from the rim.
x With the lever (T) inserted between the bead and the front section of the mounting head (I),
move the tire bead over the mounting head.
x With the lever held in this position, rotate the turntable (Y) in a clockwise direction by pressing
pedal (Z) down until the tire is completely separated from the wheel rim.
x Remove the inner tube if there is one and repeat the operation for the other bead.
In order to avoid damaging the inner tube if there is one, it is advisable to carry
out this operation with the valve about 10 cm right of the mounting head. (Fig.
16)

INNER LOCKING
x Position the clamps (G) so that they are
completely closed.
x Place the tire on the clamps and press the
pedal (V) to open the clamps and thereby
lock the rim.
OUTER LOCKING
x Position the clamps (G) according to the
reference mark on the turntable (Y) by
pressing pedal (V) down to its
intermediate position.
x Place the tire on the clamps and keeping
the rim pressed down, press the pedal (V)
as far as it will go.

5.3 MOUNTING THE TIRE
It is utmost important to check the tire and rim to prevent tire explosion during
the inflating operations. Before beginning mounting operation, make sure that:
The tire and cord fabric are not damaged. If you note defects DO NOT mount
the tire.
The rim is without dents and is not warped. Pay attention to alloy rims, internal
micro-cracks are not visible to naked eye. This can compromise the rim and can
also be a source of danger especially during inflation.
The diameter of the rim and tire are exactly the same. NEVER try to mount a
tire on a rim if you cannot identify the diameter of both.
x Lubricate the tire beads with the special grease in order to avoid damaging them and to
facilitate the mounting operations.
During rim locking MEVER keep your hands under the tire. For a correct
locking operation set the tire exactly in the middle of turntable.
x For 10 to 20 inch wheels lock the rim using the inner part of the clamps.
x For 12 to 22 inch wheels lock the rim using the outer part of the clamps.
When working with rims of the same size it is not necessary always to lock and
unlock the mounting bar; you only need to tilt and return the ram (P) with the
arm and the bar locked in their working positions.
Chains, bracelets, loose clothing or foreign objects in the vicinity of the moving
parts can represent a danger for the operator.

Never keep your hands onto the wheel: the arm recovery to “working position”
could set the operator at risk of hand crushing between rim and mounting head.
x Move the tire so that the bead passes below the front section of the mounting head and is
brought up against the edge of the rear section of the mounting head itself.
x Keeping the tire bead pressed down into the wheel rim channel with your hands, press down on
the pedal (Z) to rotate the turntable clockwise. Continue until you have covered the entire
circumference of the wheel rim (Fig. 12).
To prevent industrial accidents, keep hands and other parts of the body as far as
possible from the tool arm when the table top is turning.
x Insert the inner tube if there is one and repeat the same operations to mount the upper side of
the tire.
Demounting and mounting are always done with the clockwise turntable
rotation. Anticlockwise rotation is used only to correct operator’s errors or if
the turntable stalls.

CHAPTER 6 – INFLATING
The greatest attention is called for when inflating the tires. Keep strictly to the
following instructions since the tire changer is NOT designed and built to
protect (or anyone else in the vicinity of the machine) if the tire bursts
accidentally.
A bust tire can cause serious injury or even death of the operator.
Check carefully that the wheel rim and the tire are of the same size.
Check the state of wear of the tire and that it has no defects before
beginning the inflation.
Inflate the tire with brief jets of air, checking the pressure after every jet.
All our tire changers are automatically limited to a maximum inflating
pressure of 3.5 bar (51 psi). In any case NEVER EXCEEED THE
PRESSURE RECOMMENDED BY THE MANUFACTURER.
Keep your hands and body as far away as possible from the tire.
6.1 INFLATING TIRE USING AIRLINE GAUGE
In the standard version our tire changer are supplied with an airline gauge. To inflate a tire proceed as
follows:
x Connect the airline gauge to the tire valve.
x Make a last check to be certain that tire and rim
diameter correspond.
x Check to be certain that rim and beads are
sufficiently lubricated. If necessary lubricate some
more.
x Seat the beads with short jets of air. Between air
jets, check the air pressure on the inflator gauge.
x Continue to inflate the tire with short jets of air
and constantly checking the pressure between
until the required pressure has been reached.
EXPLOSION HAZARD!
Never exceed 3.5 bar (51 psi) when seating beads or inflating tires.
If a higher inflating pressure is required remove the wheel from turntable
and continue the inflating procedure inside a special protection cage
(commercially available).
Never exceed the max. inflating pressure given by the tire manufacturer.
ALWAYS keep hands and body back from inflating tire.
ONLY special trained personnel are allowed to perform these operations.
Do not allow other persons to operate or to stay near the tire changer.

6.2 INFLATING TIRES WITH GT SYSTEM (optional)
The GT inflating system facilitates inflation of tubeless tires to a powerful jet of air from the nozzle
positioned on the clamps.
During this phase of work he level of noise can reach 85db (A). It is advisable to
use a noise protection.
x Lock the wheel on the turntable and connect the inflating head to the tire valve.
x Make a last check to be certain that tire and rim diameter correspond.
x Check to be certain that rim and beads are sufficiently lubricated. If necessary lubricate some
more.
x Press the pedal down to intermediate position (B – Fig. 21)
x If the bead of tire is not well seated, due to a strong bead, lift tire manually until the upper bead
seats against the rim, then press pedal all the way down (C-Fig. 21). A strong jet will be
released through the nozzles in the slides and this will help the bead seal.
x Release the tires; set the pedal in the intermediate position (B – Fig. 21) and continue to inflate
the tire with short jets of air and constantly checking the pressure between air jets until the
required pressure has been reached.

EXPLOSION HAZARD!
Never exceed 3.5 bar (51 psi) when seating beads or inflating tires.
If a higher inflating pressure is required remove the wheel from turntable
and continue the inflating procedure inside a special protection cage
(commercially available).
Never exceed the max. inflating pressure given by the tire manufacturer.
ALWAYS keep hands and body back from inflating tire.
ONLY special trained personnel are allowed to perform these operations.
Do not allow other persons to operate or to stay near the tire changer.

CHAPTER 7 – MAINTENANCE
7.1 GENERAL WARNINGS
Unauthorized personnel may not carry out maintenance work.
x Regular maintenance as described in the manual is essential for correct operation and long
lifetime of the tire changer.
x If maintenance is not carried out regularly, the operation and reliability of the machine may be
compromised, thus placing the operator and anyone else in the vicinity at risk.
Before carrying out any maintenance work, disconnect the electric and
pneumatic supplies. Moreover, it is necessary to break the bead without load 3-4
times in order to let the air in pressure go out of the circuit.
x Defective parts must be replaced exclusively by expert personnel using the manufacturer’s
parts.
x Removing or tampering with safety devices (pressure limiting and regulating valves) is
extremely forbidden.
In particular the Manufacturer shall not be held responsible for complaints
deriving from the use of spare parts made by other manufacturers or for
damage caused by tampering or removal of safety systems.

7.2 MAINTENANCE OPERATIONS
¾ Clean the turntable once a week with diesel fuel so as to prevent the formation of dirt, and
grease the clamp sliding guides.
¾ Carry out the following operations at least every 30 days:
x Check the oil level in the lubricator tank. If necessary, fill up by unscrewing the reservoir F.
Only use ISO VG viscosity ISOHG class oil for compressed air circuit. (Fig. 14)
x Check that a drop of oil is injected into the reservoir F very 3-4 times the pedal U is pressed
down. If not, regulate using the screw D (fig. 14)
¾ After the first 20 days of work, retighten the clamp tightening screws on the turntable slides
(Fig. 15).
¾ In the event of a loss of power, check that the drive belt is tight as follows.
x Remove the left side body panel of the tire changer by unscrewing the four fixing screws.
x Remove the drive belt by means of the special adjusting screw X on the motor support (Fig.
16).
Before any operation disconnect the electric power supplies.

¾ If necessary to adjust the vertical arm locking plate because the tool does not lock or it does not
rise from the rim of 2mm necessary for working, adjust nuts as shown in Fig. 17.
For cleaning or replacing the silencer for opening/closing clamps, see Fig 18 and proceed as follows:
1. Remove the left side panel of the machine body by unscrewing the four fixing screws.
2. Unscrewing the silencer put on the pedal system, on the clamp opening/closing pedal.
3. Clean by a jet of compressed air or, if damaged, replace by referring to the spare parts
catalogue.
For cleaning or replacing the silencer of bead breaker, see Fig. 19 and proceed as shown on previous
point 1 and 3.

CHAPTER 8 – TROUBLE-SHOOTING
TROUBLE: POSSIBLE CAUSE: SOLUTION:
Turntable rotates only in
one direction. Reverser broken Replace reverser
Turntable does not rotate.
Belt broken Replace
Reverser broken Replace reverser
Problem with motor
Check for loose wire in the
motor, plug or socket.
Replace motor
Turntable locks Belt loose Adjust the belt tension (chap. 7
Fig. 24)
Clamp slow to open or
close Silencer clogged Clean or replace silencer
Turntable does not lock
the wheel rim correctly
Clamps worn Replace clamps
Turntable cylinder(s) defective Replace cylinder gasket
The tool touches the rim
during the tire removing
or mounting operations
Locking plate incorrectly adjusted or
defective
Adjust or replace locking plate
(chap 7 – Fig 25)
Turntable locking screw loose Tighten screw
Pedal lock out of
working position Return spring broken Replace spring
Bead breaking operation
difficult
Silencer clogged Clean or replace silencer (chap 7
– Fig. 27)
Bead breaker cylinder gasket broken Replace gasket
REV. 01 25 / 26
CHAPTER 9 – ELECTRIC AND PNEUAMTIC DIAGRAM
STANDARD ELECTRIC DIAGRAM
110V – 1PH

GT PNEUMATIC SYSTEM DIAGRAM
3 Safety Valve 10 Divider
4 Tank 11 Pressure gauge
5 Setting solenoid valve 12 Inflating unit
6 GT pedal valve 13 Deflating valve
8 Safety Valve 14 Rotation union
9 Inflating head

ED. 07/2008
PART CATALOGUE
TCͲ221XL/TCͲ229
SEMIͲAUTOMATIC TIRE CHANGER
ED. 07/2008
TAV.1Ͳ2 BODY ED. 07/08
ITEM CODE REF. NO DESCRIPTION QTY REMARK
1 3002102 YC1-3002102 Wheel support 1
2 4398848 GB/T96 Washer 6 4
3 4398108 GB/T70.1 Self-tapping screw M6X16 9
4 4399971 GB/T6182 Self-locking nut M10 1
5 3006970 YC1-3006970 Bead lifting lever 1
6 3000069 YC1-3000069 Spring 1
7 4299984 YC1-4299984 Grease cup 1
8 4398925 GB/T70.1 Screw M10X85 1
9 Air lubricator 1
10 2118258 202W-2418258 shell 1
11 2101800 YC1-3001800 Side cover 1
12 3018260 202W-3018260 ABS cover 1
13 4399998 GB/T97.1 Washer 6 7
14 3011970 YC1-3011970-1 Pedal cover 1
15 6612080 YC1-3012080 Pedal support 1
16 4399828 GB/T97.1 Washer 8 2
17 GB/T5783 Screw M8X16 2
18 4398723 GB/T70.1 Screw M6X12 2
19 3002099 YC1-3002099 Plastic foot 4
20 4399976 GB/T6170 Nut M8 2
TAV.1Ͳ2 BODY ED. 07/08
TAV.2.2 HORIZ. AND VERT. ARMS ED. 07/08
ITEM CODE REF. NO DESCRIPTION QTY REMARK
1 3002601 YC1-3012601 Mounting head shock absorber 1
2 3015586 YC1-3015586 Hexagonal arm 1
3 4398807 GB/T97.1 Washer 14 1
4 4398783 GB/T879.2 Elastic pin 4X25 1
5 3015567 YC1-3015567 Arm locking plate 1
6 4398633 GB/T97.1 Washer 10 7
7 4399971 GB/T6182 Self-locking nut M10 2
8 3005407 YC1-3005407 Spring 1
9 3001759 YC1-3001759 Operating arm knob 1
10 4399134 GB/T70.1 Screw M8X30 1
11 3012631 YC1-3012631 Arm frame 1
12 4399967 GB/T6172 Nut M10 2
13 4398900 GB/T5783 Screw M10X25 1
14 4399964 GB/T70.1 Screw M6X10 1
15 2107085 YC1-2407085 Arm locking lever 1
16 4299952 YC1-4299952 Knob 1
17 4397898 YC1-4397898 Steel shim 3
18 6615589 YC1-2415589 Horizontal arm 1
19 3000487 YC1-3000487 Hand wheel 1
20 3015565 YC1-3015565 Pivot 1
21 3007352 YC1-3007352 Washer 20.5X50X6 1
22 4399963 GB/T6182 Self-locking nut M16 1
23 2112123 YC1-2412123 Vertical arm 1
24 4399877 GB/T5782 Screw M10X60 6
25 3002214 YC1-2002214 Mounting tool 1
26 3009018 YC1-3009018 Special pin D.5 M6 1
TAV.2.2 HORIZ. AND VERT. ARMS ED. 07/08

27 5395530 GB/T80 Screw M12X12 2
28 4395805 GB/T77 Screw M12X16 2
29 3000215 YC1-3000215 Peak roll 1
30 2002215 YC1-2002215 Mounting tool unit 1
31 4395804 YC1-4395804 Washer 14.2X35X5 1
32 4395805 YC1-4395805 Washer 10.2X21X4 1
33 4399953 GB/T5783 Bolt M10X16 1
34 3006689 YC1-3006689 Plastic insert 1
35 3013650 YC1-3013650 Tool protection 1

TAV.2.2 HORIZ. AND VERT. ARMS ED. 07/08
TAV.3.2 PEDAL BOX ED. 07/08
ITEM CODE REF. NO DESCRIPTION QTY REMARK
1 2002529 YC1-2002529 Valve unit 1
2 4398999 GB/T845 Self-tapping screw ST3.5X13 6
3 3001585 YC1-3001585 Flange for valve 3001583 2
4 4299000 YC1-4299000 O-ring 17X4 12
5 3002442 YC1-3002442 Valve pin 1
6 3001584 YC1-3001584 Spacer for valve 3001583 10
7 3001583 YC1-3001583 Distribution valve 2
8 4199843 YC1-4899843 Silencer outlet adjuster G1/8Ǝ 4
9 4198954 Quick union 1/8Ǝ – 8 4
10 4198990 Quick union 1/8Ǝ – 8 1
11 3002446 Rilsan hose D8/5 L=80 1
12 3099335 Rilsan hose D8/5 L=750 2
13 2006297 YC1-2006297 Valve unit 1
14 3007598 YC1-3007598 Valve rod 1
15 4398783 GB/T879.2 Elastic pin 4X25 2
16 2002444 YC1-2002444 Valve unit 1
17 4198778 Quick union 1/8Ǝ – 8 1
18 4300145 Rilsan hose D8/5 L=900 1
19 3099335 Rilsan hose D8/5 L=750 1
20 3000144 Rilsan hose D8/5 L=700 1
21 4197629 YC1-4197629 Nylon washer 1
22 4399905 GB/T5783 Screw M6X12 3
23 4398848 GB/T96 Washer 6 1
24 4398633 GB/T97.1 Washer 10 1
25 4399890 GB/T70.1 Screw M6X20 14
26 4399998 GB/T97.1 Washer 6 16
27 4299912 YC1-4299912 Connection rod 1
TAV.3.2 PEDAL BOX ED. 07/08

28 4399891 GB/T845 Self-tapping screw ST3X6 2
29 4299910 YC1-3099910 Connection rod guide 1
30 4299913 YC1-4299913 Double cam 1
31 4299911 YC1-4299911 Forked leaf spring 1
32 4399889 GB/T6170 Nut M6 4
33 3002157 YC1-3002157 Reverser control pedal A 1
34 3007953 YC1-3007953 Bush 1
35 3000142 YC1-3000142 Pedal control spring 1
36 4397649 GB/T5782 Screw M6X50 1
37 3013333 YC1-3013333 Pedal return spring 2
38 3002161 YC1-3002161 Pedal box base 1
39 3002159 YC1-3002159 Pedal B 1
40 3003094 YC1-3003094 Pedal alignment pin 1
41 4399894 GB/T860 Elastic washer 8 1
42 4399900 GB/T6182 Self-locking nut M8 1
43 4399864 GB/T894.1 Seeger 12 2
44 4399893 GB/T6182 Self-locking nut M6 2
45 3015341 YC1-3015341 Connection rod 1
46 2001171 YC1-2001171 Connecting cable 1
47 3015345 Reverser cover 1
48 4595380 Reverser (40A) 1
49 4399996 GB/T6170 Nut M4 3
50 4399703 GB/T862.2 Toothed washer 4 3
51 2115340 YC1-2115340 Reverser support 1
52 4399905 GB/T5783 Screw M4X12 3
53 3000175 YC1-3000175 Reverser lever 1
54 4399905 GB/T70.1 Screw M4X12 1
TAV.3.2 PEDAL BOX ED. 07/08

55 4399044 GB/T70.1 Screw M5X20 2
56 3015342 YC1-3015342 Support 1
57 3005604 Grounding sticker 1
58 4399703 GB/T97.1 Washer 4 1
59 2006040 Grounding cable 1
60 4599986 Cable holder 1
61 Electric cable 1
62 GB/T5783 Screw M8X16 3
63 4399829 GB/T97.1 Washer 8 3
64 2015861 YC1-2015861 Pedal control unit 1

TAV.3.2 PEDAL BOX ED. 07/08
TAV.4.2 BEAD BREAKER ED. 07/08
ITEM CODE REF. NO DESCRIPTION QTY REMARK
1 3005053 YC1-3005053 Cylinder liner 1
2 4394969 GB/T6171 Nut M18X1.5 1
3 4398289 GB/T97.1 Washer 18 1
4 4195069 YC1-4195069 Seal 1
5 3016806 YC1-3016806 Cylinder piston 1
6 3015834 YC1-3015834A Piston rod 1
7 4198145 GB/T3452.1 O-ring 195X5.1 1
8 2115571 YC1-2415571 Cylinder flange 1
9 4399892 GB/T5783 Screw M6X16 12
10 4398007 GB/T6177 Flange nut M6 12
11 3015573 YC1-3015573 Bush 2
12 4399943 GB/T70.1 Screw M12X35 2
13 3000889 Rilsan hose 8×5 L=700 1
14 4198578 Rotation union 1/4Ǝ 8 2
15 2015572 YC1-2015572 Bead breaker cylinder 1
16 4298168 GB/T3452.1 O-ring 20X2.75 2
17 3199601 Scraper 20X30X7 1
18 4398146 YC1-4398146 Shim 24X30X0.5 1
19 3199599 GB/T893.1 Seeger 30 1
20 4399971 GB/T6182 Self-locking nut M10 1
21 4397145 GB/T70.1 Screw M10X70 1
22 3000114 YC1-3000114 Arm spring 1
23 4399945 GB/T5782 Screw M16X90 1
24 2412271 YC1-2412271 Bead breaker plate 1
25 4398899 GB/T955 Elastic washer 14 2
26 4398178 GB/T894.1 Seeger 40 2
27 3008990 YC1-3008990 Pivot pin 1
TAV.4.2 BEAD BREAKER ED. 07/08

28 4299952 YC1-4299952 Knob 1
29 4399963 GB/T6182 Self-locking nut M16 1
30 6615574 YC1-2415574 Bead breaker arm 1
31 4396941 GB/T6172 Nut M14 2
32 YC1-002 Rubber limit 1
TAV.4.2 BEAD BREAKER ED. 07/08
TAV.6Ͳ20r SELFͲCENTERING TURNTABLE ED. 07/08
ITEM CODE REF. NO DESCRIPTION QTY REMARK
1 2015845 YC1-2015845 Turntable system 1
2 3015187 YC1-3015187 Guide pin 8
3 3009778 YC1-3009778 Washer 16.3X47X13 1
4 3000062 YC1-3000062 Turntable cap 1
5 4399926 GB/T5783 Screw M16X1.5X40 1
6 2112865 YC1-2112865 Turntable 1
7 3006255 YC1-3006255 Slide 4
8 2115756 YC1-2415756 Slide guide 2
9 4398637 GB/T97.1 Washer 12 8
10 4399864 GB/T894.1 Seeger 12 4
11 3002901 YC1-3002901 Cylinder shaft 2
12 4198856 YC1-4198856 Piston 2
13 4399865 GB/T6182 Self-locking nut M12 2
14 Rotation union 1/8Ǝ 8 1
15 3199601 Scraper 20X30X7 2
16 4398146 YC1-4398146 Washer 24X30X0.5 2
17 3199599 GB/T893.1 Seeger 30 2
18 4299168 GB/T3452.1 O-ring 20X2.75 2
19 4397678 GB/T6177 Flange nut M8 8
20 3015023 YC1-3007941 Special screw 8
21 3002293 YC1-3015023 Back flange 2
22 3008042 YC1-3008042 Cylinder liner 2
23 4298822 GB/T3452.1 O-ring 75X3.55 4
24 4198898 Union 1/8Ǝ 8 2
25 Rilsan hose 8X5 L=70 2
26 3002225 Rilsan spiral hose 8X5 L320 1
27 T union D.8 1
TAV.6Ͳ20r SELFͲCENTERING TURNTABLE ED. 07/08

28 3015024 YC1-3015024 Front flange 2
29 3002225 Rilsan hose 8X5 L=850 2
30 3199589 GB/T3452.1 O-ring 60X2.65 3
31 3015169 YC1-3015169 Turntable plate 4
32 2008060 YC1-2008060 Turntable cylinder unit 2
33 3099335 Rilsan hose 8X5 L=270 2
34 3006870 YC1-3006870 Connection plate 8
35 4399932 GB/T894.1 Seeger 65 1
36 4398037 GB/T70.1 Screw M10X1.25X25 4
37 3002297 YC1-3002297 Oversize clamp 4
38 2115755 YC1-3015755 Slide guide 2
39 3006879 YC1-3006879 Turntable spacer 4
40 3006880 YC1-3006880 Connection rod spacer 4
41 4398637 GB/T97.1 Washer 12 4
42 4398838 GB/T70.1 Screw M12X1.25X45 4
43 4298955 YC1-4298955 Rotation union 1
44 2006393 YC1-2006393 Clamp cover 4
45 4198954 Quick union 1/8Ǝ 8 2
46 Quick T union 1/8Ǝ 8 1
47 GB/T5783 Screw M6X12 4
48 4399889 GB/T6170 Nut M6 4
49 3006878 YC1-3006878 Connection pin 4
50 3006869 YC1-3006869 Turntable flange 2
51 3007420 YC1-3007420 Bush 1
52 3006869 YC1-3006869-A Turntable spacer 1
TAV.6Ͳ20r SELFͲCENTERING TURNTABLE ED. 07/08
TAV.7Ͳ4 SELFͲCENTERING TURNTABLE GT ED. 07/08
ITEM CODE REF. NO DESCRIPTION QTY REMARK
1 2015856 YC2-2015856 GT turntable 1
2 3015187 YC1-3015187 Guide pin 12 8
3 3009778 YC1-3009778 Washer 16.3X47X13 1
4 3000062 YC1-3000062 Turntable cap 1
5 4399926 GB/T5783 Screw M16X1.5X40 1
6 2107384 YC2-2107384 Turntable 1
7 2107387 YC2-2407387 GT slide 4
8 2115756 YC1-2415756 Slide guide 2
9 4398637 GB/T97.1 Washer 12 8
10 4399864 GB/T894.1 Seeger 12 4
11 3002901 YC1-3002901 Piston rod 2
12 4198856 YC1-4198856 Piston 2
13 4399865 GB/T6182 Self-locking nutM12 2
14 2006393 YC1-2006393 Clamp cover 4
15 3199601 Oil scraper 20X30X7 2
16 4398146 YC1-4398146 Shim 24X30X0.5 2
17 4198035 GB/T893.1 Seeger 30 2
18 4299168 GB/T3452.1 O-ring 20X2.75 2
19 4397678 GB/T6177 Flange nut 8
20 3007941 YC1-3007941 Special screw 8
21 3015023 YC1-3015023 Back flange 2
22 3008042 YC1-3008042 Cylinder liner 2
23 4298822 GB/T3452.1 O-ring 75X3.55 4
24 4198898 90º union 1/8Ǝ – 8 2
25 Rilsan hose 8X5 L=70 2
26 3002225 Rilsan spiral hose 8X5 D.60X3 1
TAV.7Ͳ4 SELFͲCENTERING TURNTABLE GT ED. 07/08

27 T union D.8 1
28 3015024 YC1-3015024 Front flange 2
29 4198954 Quick union 1/8Ǝ – 8 2
30 Rilsan hose 8X5 L=270 2
31 3015169 YC1-3015169 Turntable plate 4
32 2008060 YC1-2008060 Turntable cylinder 2
33 4398037 GB/T70.1 Screw M10X1.25X25 4
34 2002297 YC1-3002297 Oversize clamp 4
35 2115755 YC1-3015755 Slide guide 2
36 3006879 YC1-3006879 Turntable spacer 4
37 3006880 YC1-3006880 Connection rod spacer 4
38 4398637 GB/T97.1 Washer 12 4
39 4398838 GB/T70.1 Screw M12X1.25X45 4
40 GB/T5783 Screw M6X12 4
41 4399889 GB/T6170 Nut M6 4
42 3006878 YC1-3006878 Pin 4
43 3006869 YC1-3006869 Turntable flange 2
44 3007420 YC1-3007420 bush 1
45 4399932 GB/T894.1 Seeger 65 1
46 3006870 YC1-3006870 Connection plate 8
47 3002109 Rilsan hose 14X11 L=700 2
48 4198035 Quick union 1/4Ǝ 10 4
49 3006478 Rilsan hose 10X6.5 L=400 4
50 4197207 T union 1/8Ǝ 10 4
51 3006477 Rilsan hose 10X6.5 L=300 4
52 4298992 YC2-4298992 Rotation union 1
53 Union 1/8Ǝ 8 1
TAV.7Ͳ4 SELFͲCENTERING TURNTABLE GT ED. 07/08

54 3001996 GB/T77 Screw M6X25 2
55 4298802 GB/T3452.1 O-ring60X2.65 3
56 T union 1/8Ǝ – 8 1
57 3099335 Rilsan hose 8X5 L=850 2
58 3006869 YC1-3006869-A Flange spacer 1

ITEM CODE REF. NO DESCRIPTION QTY REMARK
1 4399900 GB/T6182 Self-locking nut M8 10
2 3010873 YC1-3010873 Bottom part of reduction gear box 1
3 4296910 GB/T276 Bearing 6212 1
4 4396948 GB/T1096 Tab 16X10X70 1
5 3010885 YC1-3010885 Helical gear stud 1
6 4399664 GB/T70.1 Screw M6X10 2
7 3010884 YC1-3010884 Helical gear 1
8 4396946 GB/T894.1 Seeger 60 1
9 4296943 GB/T3452.1 O-ring 34.5X3.55 2
10 4396947 GB/T1096 Tab 6X6X18 1
11 3010883 YC1-3010883 Worm 1
12 4296944 GB/T297 Bearing 30204 2
13 2100166 YC1-3000166 Motor pulley 1
14 3010886 YC1-3010886 Sealing cap 1
15 4296945 GB/T279 Bearing 6212 2RS 1
16 4296942 YC1-4296942 O-ring 20X35X10 1
17 3199596 YC1-3199596 Gear box pulley 1
18 4396940 GB/T119.1 Pin 8X20 2
19 3010872 YC1-3010872 Upper part of reduction gear box 1
20 4399134 GB/T70.1 Screw M8X30 10
21 2011967 YC1-2011967 Reduction gear unit 1
22 4299923 GB/T11544-1997 Belt V A580 1
23 4396941 GB/T6172 Nut M14 1
24 4398807 GB/T97.1 Washer 14 1
25 4399922 GB/T79 Screw M8X14 1
26 4398633 GB/T97.1 Washer 10 8
27 4399829 GB/T97.1 Washer 8 4
TAV.7Ͳ1 MOTOR – REDUCTION GEAR GROUP ED. 07/08

28 4399976 GB/T6170 Nut M8 4
29 Motor 1
30 3000164 YC1-3000164 Belt-stretcher shoe 1
31 4399966 GB/T5783 Screw M10X20 2
32 4399935 GB/T5783 Screw M8X25 4
33 3000149 YC1-3000149 Motor support 1
34 4399880 GB/T5783 Screw M10X35 1
35 4399969 GB/T6170 Nut M10 1
36 4399933 GB/T5782 Screw M10X50 6
37 4396700 GB/T894.1 Seeger 50 1

TAV.7Ͳ1 MOTOR – REDUCTION GEAR GROUP ED. 07/08
TAV.9Ͳ2 AIR LUBRICATION GROUP ED. 07/08
ITEM CODE REF. NO DESCRIPTION QTY REMARK
1 4198173 Regulator 1/4Ǝ 3.5bar 1
2 4198435 Safety valve 1/8Ǝ 4bar 1
3 4198884 Union 1/4Ǝ 8 3
4 2010781 YC1-2010781 Pressure regulator unit 1
5 4198883 Quick union 1/4Ǝ 8 3
6 4199797 Nut 1/4Ǝ 1
7 9298243 Inflating gauge 1
8 4196315 Lubricator cap 1
9 4198818 T union 1/4Ǝ 8 1
10 4198143 Valve 1/4Ǝ F-F 1
11 4199987 Union 1/4Ǝ 1
12 2012326 YC1-2012326 Lubricator unit 1
13 4196316 Lubricator cap 1
14 4198951 Regulator 1/4Ǝ 10bar 1
15 2014217 YC2-2014217 GT pressure gauge 6212 2RS 1
TAV.9Ͳ2 AIR LUBRICATION GROUP ED. 07/08

Warranty
This item has a one (1) year LIMITED warranty.
Atlas® Automotive Equipment warrants the equipment to the
original purchaser against defects in material or workmanship
under normal use for a period of one year from the date of
purchase. This warranty shall be limited to the replacement of
materials or parts found defective, at the discretion of Atlas®
Automotive Equipment and/or its authorized distributors. This limited one (1) year warranty
DOES NOT apply to normal wear items (turntable jaws, belts, gauges, plastic jaw protectors,
etc.). The limited one (1) year warranty does not include a labor warranty. Warranties do not
apply to items that have been abused or misused.
Returned goods must be authorized to be returned (in writing) by Atlas® Automotive Equipment
and/or an authorized distributor and must be prepaid to a designated location. All returns may
be subject to a 15% handling and restocking charge. Returned goods must be in like-new
condition complete with warranty and original shipping papers.
Customer’s Responsibilities
• Shall ensure that all air operated components are properly maintained
• Shall ensure components are powered by well lubricated and moisture free compressed air
(if a suspected defective part has not been properly lubricated it will not be covered under
warranty)
• Shall establish procedures to periodically maintain and inspect the equipment
• Shall ensure that your wheel balancer is protected by a surge protector
• Shall ensure that all equipment shall have adequate amperage service
THIS WARRANTY IS EXCLUSIVE AND IS LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED INCLUDING ANY IMPLIED WARRANTY OR MERCHANTABILITY OR ANY IMPLIED
WARRANTY OF FITNESS FROM A PARTICULAR PURPOSE, AND ALL SUCH IMPLIED WARRANTIES
ARE EXPRESSLY EXCLUDED.
THE REMEDIES DESCRIBED ARE EXCLUSIVE AND IN NO EVENT SHALL THE MANUFACTURER,
NOR ANY SALES AGENT OR OTHER COMPANY AFFILIATED WITH IT OR THEM, BE LIABLE
FOR SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR THE BREACH OF OR DELAY
IN PERFORMANCE OF THIS WARRANTY. THIS INCLUDES, BUT IS NOT LIMITED TO, LOSS OF
PROFIT, RENTAL OR SUBSTITUTE EQUIPMENT OR OTHER COMMERCIAL LOSS.
For warranty assistance, please call 866-898-2604. Please have your invoice number ready so
that we may be able to serve you better. Warranty procedures cannot be initiated without an
invoice number corresponding to the product serial number.
For further product and distributor information, please visit www.atlasautoequipment.com

atlas tire changer tc489xrf, atlas tire carrier, atlas tire machine repair, atlas trenchless, atlas trenching website, atlas tree care, atlas tire changer calgary, atlas tire changer 221, atlas tire changers tc289, atlas tire machine tc 12,

Disclaimer : I need to confirm! That the contents of Atlas Tire Changer Manual, This only Preview only includes pictures and videos from Atlas Tire Changer Manual. For more information from Atlas Tire Changer Manual PLEASE PLAY VIDEO UNDER THIS :

Atlas Manual Bead Roller Arm (MBR) atlas tire changer manual
267943 Atlas Tire Changer Manual publish atlas-tire-changer-manual Throughout this manual, the following symbols and printing characters are used to facilitate reading: Indicates the ….. The operation of the tire changer is divided into three parts: …… Atlas® Automotive Equipment warrants the equipment to the. Throughout this manual, the following symbols and printing characters are … A complete description of the “Tire Changer Model” and the “Serial number” will make it easier for ….. Atlas® Automotive Equipment warrants the equipment to the.

Read the entire manual thoroughly and make sure you understand it. 1.2 TYRE CHANGER IDENTIFICATION DATA. A complete description of the “Tire Changer .Throughout this manual, the following symbols and printing characters are … thanN you for purchasing a product from the line of Automatic tire changers. the The manual bead roller arm is a simple yet effective tool to assist with removing and replacing tires when changing them Change tires quickly and speed up service in your shop with top-quality tire changers. Find affordable tire changers at wholesale prices with Atlas Auto Equipment.

There is some assembly required on the Atlas TC 221 wheel clamp tire changer. Atlas Auto Equipment stocks a complete line of parts for all the Atlas wheel USE AND MAINTENANCE MANUAL AUTOMATIC CAR TIRE CHANGER ATLAS TC-733 REV. 01 1 / 26 PRINTING CHARACTERS AND SYMBOLS Throughout Discover 500,000+ Repair & Service Manuals for Construction, Electronics, & More. Great Experience. “Easy Process.” “Simply Fast.” A Selection From +9,000 5-Star Reviews. Instant Download. Latest Models Covered. Services: DIY Servicing, DIY Smog Checks.

What about image over? is usually that will incredible???. if you’re more dedicated thus, I’l m show you many impression once again below:

$ 3 JPG
Atlas Tire Changer from atlas tire changer manual , source:ebay.com

atlas tc289 electric pneumatic wheel clamp tire changer gses the atlas tc 289 wheel clamp tire changer is the perfect wheel clamp tire changer for most general automotive service departments and medium sized tire stores this tire changer is perfect for changing the tires on large suv and one ton trucks atlas tc289lh tire changer gregsmithequipment the atlas tc289lh wheel clamp tire changer is the atlas tc289 wheel clamp tire changer that has been equipped with the pneumatic atlas lh assist arm the addition of the atlas lh assist arm to the atlas 289 makes the atlas tc289lh one of the most powerful wheel clamp tire changers in the marketplace the atlas tc289lh is the perfect wheel clamp tire changer for most general use and maintenance manual

automatic car tire changer use and maintenance manual automatic car tire changer atlas tc 733 this manual is an integral part of the manual it shall be given to the new owner if and when the • the tire changer must be transported in its original packaging and kept in the position shown atlas equipment tc221 tire changer atlas tc 221 tire changer offers nothing but convenience it is flexible to change all kinds of tires from steel wheels up to the most expensive alloy wheels while delivering protection to your rims and tires solved atlas tc229 tire changer fixya hi anonymous keeping proper tire air pressure smaller windshield less weight a properly tuned engine go down one size on the main jet i am sorry you can t find the first and best tool you ever bought for your atlas honda but despair not for a mere $10 you can another one printing characters and symbols indicates the operations printing characters and symbols throughout this manual the following symbols and printing characters are used to facilitate reading indicates the operations which need proper care • the tire changer es plete with instruction and warning transfers which are designed to be long lasting atlas tire changer find great deals on ebay for atlas tire changer shop with confidence tire changers clarke s southern truck parts our products the atlas 229 has the same clamping and tire changing capabilities as the atlas tc 221 wheel clamp tire changer but has the added bead blaster system to help inflate stiff sidewall tires or other “hard to inflate” tires tire

changers atlas auto equipment change tires quickly and speed up service in your shop with top quality tire changers find affordable tire changers at wholesale prices with atlas auto equipment parts breakdown manuals brochures catalogs parts breakdown manuals brochures catalogs atlas copco piston pressor ls lp balcrank accessories catalog 2010 coats 5000 series tire changer catalog coats 9024e tire changer parts breakdown coats heavy duty tire changer catalog coats rc 50m corghi a2024 t i parts list

$ 3 JPG
$ 3 JPG

Thanks for visiting our site, articleabove Atlas Tire Changer Manual
published by at . Today we’re excited to announce we have discovered an awfullyinteresting topicto be discussed, that is Atlas Tire Changer Manual
Many people looking for details aboutAtlas Tire Changer Manual
and certainly one of these is you, is not it?

Leave a Reply

Your email address will not be published. Required fields are marked *